February 3, 2012
As part of their 25th Anniversary Celebrations R&M are pleased to announce the first stage of their commemorative year festivities by launching the long awaited “Technical” area of their website.
The section went live on the 1st of February and has been developed to bring together all the vast technical knowledge available through R&M into one convenient location.
Specifically designed to focus on the diverse specialist markets supplied by R&M the area has particular relevance to those working in hazardous areas, both in the international and domestic markets.
The Technical Area has been split into 7 distinct areas for ease of use:
- General Information – contains information regarding certificates and permits, product conversion tables and comparison charts.
- Hazardous Area – a specific area designed to impart information regarding ATEX and DSEAR compliance.
- Product Guidance Notes – a developing section to aid users in the use of particular products.
- Product Selection Charts – focusing on hazardous area selection charts e.g. Hawke Gland selection.
- Technical Data Sheets
- Technical Information – with particular focus on Cable Specification
- Technical Training – highlighting the training and advice R&M are able to provide with regards to the complex legislation surrounding working in hazardous area conditions.
“We are delighted with the Technical Area and hope that users of our website find it useful. The area has been specifically conceived to be constantly updated, with new information being added all of the time – R&M welcomes any feedback or suggestions users of the area may have to make the area more informative and user friendly!” comments Rachal Wilson (Commercial Manager).
June 30, 2011
Have You Considered The Proven Alternative to Traditional Methods Of Installing Building Services?
R&M Fixings & Supports Ltd have joined forces with MEP Solutions, who are a market leader in modular mechanical and electrical services engineering and specialists in integrated prefabricated solutions to the construction and building services industries.
With over nine years’ experience in the construction industry, MEP Solutions Ltd is a market leader in the design, manufacture and installation of multi-service modules, incorporating pipework, ventilation ductwork and electrical containment systems.
Each unique module is designed from fully co-ordinated 3D models and manufactured under factory controlled conditions. Modules are then delivered to site on a just in time basis, thus reducing the number of on-site personnel, reducing waste and improving installation efficiency.
MEP Solutions has gained significant experience across all market sectors.
Prestigious projects completed to date include;
• Healthcare: Peterborough Hospital, Enniskillen Hospital, St Bartholomew’s
• Hospital, Glasgow Southern General Hospital.
• Commercial: Piccadilly Place, Bridgewater Place, Eldon Square, The Cube.
• Education: South Leicester College, Middlesbrough College, Dunoon Grammar School, Retford and St. Giles Schools.
Do you need 3D Co-ordination Services?
We are also able to offer our engineering and co-ordination expertise to provide fully co-ordinated 3D solutions to any project, including those to be installed in the traditional manner, using the latest market leading software applications.
If you would like to know more, please feel free to contact us to discuss your requirements.
Tel: 023 8038 6800 Email: fixings@rm-electrical.com
March 28, 2011
R&M Fixings & Supports Ltd now stocks the Fischer High Performance FAZ II range of Anchor Bolts.
Key Features of this bolt are:
- Highest tensile and shear loads, that means: more safety with fewer total fixing points and thus lower costs
- Can be used in extremely thin concrete panels, starting at 8cm thickness
- Smalles edge distances and axial spacings for more application options
- Low driving-in energy, small tightening distance and thus extremely handy for installation work
- High steel ductility enables subsequent alignment using a hammer
- Installation friendly, since only a few revolutions are necessary to apply the torque
- Push through and pre-positioned installation
“This is a wonderfully designed bolt which can be used in both cracked and non-cracked concrete. Its high tensile and sheer load ratings means the installation has fewer fixing points – thus saving money all round! It is perfect for use with extremely thin panels (8 cm) and can be aligned after installation” Nick Dyer-Smith (Director)
March 22, 2011
R&M Fixings & Supports Ltd have joined forces with MEP Solutions, who are a market leader in modular mechanical and electrical services engineering and specialists in integrated prefabricated solutions to the construction and building services industries.
Our new service offers you the design and manufacture of insulated and pressure tested prefabricated multi-service modules including and not limited to – pipework, duct-work, medical gases and all electrical services.
R&M’s pre-fabrication service offers a complete build solution and technical support from conception through to completion offering a flexible and practical approach for our clients.
Our manufacturing facility applies the latest prefabrication design and innovation expertise in the production of the highest quality mechanical and electrical modules for both the new build and refurbishment projects.
Our engineering function provides expert technical and tendering support to our clients with full 2D and 3D drawing co-ordination support. We operate the latest industry design Auto CAD software which works in synergy with the patented bespoke modularisation software developed in-house by MEP.
The results of using pre-fabricated modules are a reduction in capital costs, construction time and defects with the added benefit of enhanced predictabillity, productivity, quality and a reduction in the need for skilled labourers.
Contact R&M Fixings for information on our pre-fabrication requirements on 023 8038 6800 or fixings@rm-electrical.com
February 28, 2011
Now available through our Assembly Division – the new CEAG range of nLLK 10 Ex-Light Fittings.
Combining latest lighting engineering with the specialist requirements of harsh and hazardous environments these luminaires are certified for use in Zone 2 gas Ex-areas and Zone 22 dust EX-areas.
Additional benefits offered by this range are:
- Energy savings
- Cost Efficient Installation
- High Safety
- Easy Maintenance
- High Degree of Protection IP66
Click here for more information and technical specifications or contact our assembly division on 023 8068 6618. assembly @rm-electrical.com
February 21, 2011
R&M’s Assembly Division have innovatively expanded their “stable” of services by taking delivery of the cutting edge, high tech marker printer – the Weidmuller “PrintJet PRO”.
The PrintJet PRO is the benchmark for industrial printing, and is renowned for producing markers with high definition print quality with superior smudge and scratch resistance. The cutting edge technology encapsulated within the PrintJet PRO will enable R&M to reliably produce high quality, small or large volume markers to our customer’s exact specifications.
“The innovative technology within the PrintJet PRO gives us the flexibility to produce both colour and monochrome markers that are of the highest quality but with the additional advantage of the flexibility of allowing us to produce large batches at short notice – if so desired by our customer! The Assembly Division has built its reputation on quality of product and the flexible service it is able to offer its customers – and as such the PrintJet PRO compliments our ethos perfectly!” Neil Sherin (Assembly Division Manager).
Contact R&M Assembly Division today for all your marker requirements, we are able to offer a reliable, quality, bespoke service at competitive prices, tailored to your personal requirements! Assembly@rm-electrical.com, Tel: 023 8068 6618
